Since you don’t have x-ray vision, how do you see the pit before you bite it?
- Category Archives Life Hack
Did you know that if you are not careful, converting a single flush system to a dual flush system could actually waste more water? Using our optimal installation guide, we show you how to measure your water so that you can save the most water. We spent a lot of time on the adjustment because if each person flushes 6 times daily, that is 2000 flushes a year per person.
The installation instructions from the manufacturer aren’t the best. First, it didn’t discuss how to adjust the blue clamp on the refill valve. Second, adjustment for the half flush from this manufacturer may require you to waste too much water before finding the right point on the dial. We provide the optimal Golden Section solution to waste a minimal amount of water while testing.
If you decide to purchase the real dual flush kit, here are couple of links for the products:
for Fluidmaster DUOFLUSH Fluidmaster DUOFLUSH
for Danco Dual Flush: Dual Flush by Danco at Amazon
People who are accustomed to the single flush system may accidentally push the lever down when they intended to half flush. Since liquid waste is more frequent than solid waste, pushing down the lever by mistake would cause more water waste. In this video we provide one simple solution to swap the half dial and the full dial.
Since different viewers may have different questions in mind, here are the timestamps so that you can click and skip to the sections you’re interested in:
The Golden Section algorithm description:
Swapping the half dial and the full dial:
Flush valve dial adjustment:
Refill Valve installation:
The blue clamp on the refill valve adjustment:
What to do if the dial adjustment is out of range:
If you have the “dual flush” system from Danco, you can watch this video:
Save Water: Convert Toilet into Dual Flush, Best Install, Explanation & Tips
A few toilet or plumbing related issues can be found below:
Slow Draining: Easy 5 Seconds Toilet Flush Test and Solving the Slow Flush Mystery
5 Different Ways To Make Your Toilet Use Less Water
Toilet siphon effect, when plunger, auger and snake fail:
Big Mystery of the Adjustable Toilet Flapper Solved
5 Ways To Unclog Toilet Using A Garden Hose
How To Unclog Bathroom Sink
How To Unclog Kitchen Sink
We’ve all had the annoying moment when we just couldn’t open that jar. Lucky for you, if you watch my video, you’ll never again have to watch any other.
My ways are guaranteed to help you no matter what situation you’re in, and no matter what kind of jar it is. Whether the jar is vacuum sealed or stuck with honey or something else, I’ve got you covered!
Don’t forget to subscribe for more genius videos.
You may always want to know the best way to do things. The best way depends on what is the problem. The problem could have different causes.
If you just want to purchase your opener, here is the link: Opener
If you could not open a jar, it could simply because you were turning it in the wrong direction, but assuming you didn’t make that mistake, there is only one reason why you can’t open it. That is, your force can’t overcome the resistance of the jar. For that, you may blame either the person or you may blame the jar. 🙂
If you prefer to blame the person, there are 2 possibilities. You either have weak fingers or a weak wrist/arm.
Weak fingers can’t apply sufficient force perpendicular to the surface to generate sufficient friction, thus your hand slips. To compensate for this, we can use many non-slip materials: rubber glove, leather glove, wide rubber band, balloon.
To turn the lid, you should use your arm instead of your wrist to turn the lid, because your arm is much stronger, and wrists can be easily injured.
If you feel that your weak wrist or arm is the problem, you can leverage your force by using tools with long handles. The longer the handle, the less force is needed. For example if you can extend the length of the pipe wrench, or the oil filter wrench, you will gain more power.
If you think the jar is the problem, you need to investigate the 3 possibilities of what is causing the high resistance.
The 3 causes are the vacuum seal, high friction on the threads and liner, or solidified food. You need to match the tools you have to solve each problem.
Two solutions to break the vacuum: either prying or tapping.
Prying: you may buy special tools, or you can use a beer bottle opener, a spoon, a butter knife or a screwdriver to poke around the jar’s perimeter so that you can introduce an air leak and break the vacuum.
Tapping: You may use a wooden cooking utensil to whack the top of the lid. You need to whack it hard but not so hard that you break the glass. You hope it will break the vacuum as well as unstuck the lid. You can also use the back of a knife to whack as long as you’re careful.
If a jar is vacuum sealed, then there is often a seal button, see here. If this button or the lid pops up, it means the vacuum is broken. If you have high friction on the threads, you may use a heating method. Reduce friction: Heating the metal lid will reduce the force needed because metal will expand more than glass.
The heat source could be your stove, hot water, hair dryer or cigarette lighter.
There are two common types of jar lid, one is continuous threaded where the jar and lid are both threaded in one continuous bead. It is similar to a nut and bolt. To open it, you need to turn at least 360 degree. Since the thread is long and gradual, you may potentially have a tighter seal, thus it may be harder to open it.
The second type is lug or called twist-off type where the container has multiple threads and the lid has an equal number of lugs or tabs that grip the corresponding threads. You can see a few nubs here. To open it, typically you need to turn the lid less than 90 degree. This is easier to keep clean and free from sticky product.
Sometimes a jar that has been opened before will still be tough to open if the contents are something sticky, like honey. When the lid is heated, the honey or other sticky substance should soften or melt, making it easier to twist open.
Finally, if you have a jar of honey or something sticky, you can put some plastic wrap over the thread so that it will be easy for you to open it next time.
Note: if you heat the jar, you may not heat too long because even though the vacuum has negative pressure, heating would generate vapor and thus may create positive pressure and explode.
— Genius Asian (@RealGeniusAsian) May 8, 2018
No need to watch other people’s videos since this video covers all! The cheapest and easiest ways for all different situations are covered. No problem even if you don’t have any equipment.
There are 5 Billion mobile phone users in the world. For various reasons, you may sometimes need to place or attach the cell phone to somewhere where there is no obvious mechanism for attaching it. In addition, perhaps you do have regular proper holders or adapters, but since you go to different places with your mobile phone, you may be somewhere where you do not have the access to your usual gear, hence we have provided many different ideas in this video.
I promise some of these ideas cannot be found anywhere else. To make a DIY device, other people may say buy this and buy that, but I always use what I have on hand. So bear with me for the longer video since I will show you various different ways that can then be adapted to suit your own situation and inspire you to create something new.
I have published couple of related videos in the past, here are the links:
“Build an easy & free home security system in under 5 minutes” https://youtu.be/CRT_vxjXlI4
“The Cheapest and Simplest DIY Cell Phone/GPS Mount in a Car” https://youtu.be/j3li8pam1d0
— Genius Asian (@RealGeniusAsian) December 11, 2018
The smoke from California fires caused air purifiers to be sold out at many locations. Today I am going to show you how to use what you have or can probably still get, to the room air clean. Compared with the expensive air purifiers on the market, these DIY air purifiers are equivalent but at a much cheaper price.
Three reasons they are cheaper:
1. if you already own a fan, then you don’t have to buy another fan.
2. when buying filters, you can buy whatever size is most suitable for your fan, or is cheaper
3. unlike air purifiers, the filters as well as fans can be bought cheaply (because both items are high volume commodities).
For example both the fans and the filters can be bought for about $15 each.
— Genius Asian (@RealGeniusAsian) November 18, 2018